Winco-mfg 8570D1 - Treatment Table with Drawers Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Meubles Winco-mfg 8570D1 - Treatment Table with Drawers. Winco Mfg. 8570D1 - Treatment Table with Drawers User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Page 1 of 4
006080 Rev M Date 06-06-12 JWC
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER stand on table or INJURY MAY OCCUR.
3. NEVER allow user to sleep unattended on table or INJURY MAY OCCUR.
4. NEVER leave an unconscious user unattended on table or INJURY MAY OCCUR.
5. DO NOT use table for transporting user in or with ANY type of vehicle or trailer. Winco tables have not been tested
or approved for use by an occupant in any type of vehicle or trailer.
6. NEVER leave an infant or child unattended on table or INJURY MAY OCCUR.
7. DO NOT put hands, feet or clothing into any openings when changing positions on table. Attendant MUST confirm
that users hands and feet are clear of all moving parts while changing table positions or INJURY MAY RESULT.
8. Periodically, recheck tightness of all nuts, bolts and screws.
9. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
10. NEVER EXCEED the recommended weight capacity of 400 lbs. (181.4 kg).
11. SAVE THESE INSTRUCTIONS for future reference and training.
8570
Adjustable Headrest Treatment Table
with Cabinets and/or Drawer Modules
CUSTOMER INSTRUCTIONS
Tools needed:
Scissors or box cutter
Phillips-head screwdriver
½” wrench or ½” socket & ratchet wrench
7/16” wrench, (multiple size wrench included to check pre-installed fasteners for tightness after
shipping)
- If using powered tools always start hardware together by hand first & wear safety goggles
SEE “Parts Reference” (pg.3) for visual reference.
1. After checking your product for any shipping damage, remove all packing material and hardware that was
secured for shipping.
2. Use a ½” wrench or socket, and remove the four (4) bolts that are attaching the table to the skid. (Bolts go
through the plastic Threaded Inserts in ends of table legs, and the shipping skid.)
3. Using at least (2) people, lift the table off of the skid.
4. Install the included Adjustable Glide Feet into the Threaded Inserts, located in the bottom the table legs.
(see note).
NOTE: Turning table on side or vinyl-side down will ease this installation, however, drawers should
be removed. Please protect your Upholstered Top with cardboard, clean carpeted floor, etc… when
performing this operation. Use of two or more people is HIGHLY recommended.
5. With table in the upright position, adjust the (4) Adjustable Glide Feet to level the table.
6. Use a Phillips bit screwdriver and a 7/16” wrench to check all screws, nuts, and bolts to ensure they are tight
and did not loosen during shipping.
7. Load paper roll onto Paper Holder Rod. Rod must be inserted through Paper Rod Clamps.
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions contact your dealer or Winco customer support, (800) 237-3377
before attempting to use this product; otherwise injury may occur.
8570 Weight Capacity = 400 lbs. (181.4 kg.)
Winco assumes no responsibility for damage or injury caused by the improper assembly, installation
or use of these products; or during assembly or maintenance of these products.
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - CUSTOMER INSTRUCTIONS

Page 1 of 4 006080 Rev M Date 06-06-12 JWC 1. READ AND FOLLOW ALL DIRECTIONS. 2. NEVER stand on table or INJURY MAY OCCUR. 3. NEVER allow u

Page 2 - Operation of Table

Page 2 of 4 006080 Rev M Date 06-06-12 JWC Operation of Table  To raise the Upholstered Backrest, pull black lever on the Remote Release System

Page 3 - Parts Reference

Page 3 of 4 006080 Rev M Date 06-06-12 JWC Parts Reference

Page 4

Page 4 of 4 006080 Rev M Date 06-06-12 JWC

Commentaires sur ces manuels

Pas de commentaire